Scope. Outdoor design conditions and illustrative block loads for homes in and around Tampa, FL. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.
Tampa design conditions
| Weather station | Tampa International Airport (KTPA) |
|---|---|
| Source | NOAA NCEI Engineering Weather Data, 1988–2017 observations |
| Elevation | 26 ft |
| 99% heating design temperature (NOAA/ASHRAE) | 43°F |
| 1% cooling design temperature (NOAA/ASHRAE) | 91°F |
| Mean coincident wet bulb | 77°F |
| Design grains (75°F, 50% RH indoors) | 53 |
| Daily range | Low (July average 13°F) |
| IECC climate zone | 2A (Hillsborough County, 2021 IECC) |
With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 27°F difference and the cooling load by a 16°F difference, before sun, people and moisture are added. 53 design grains is a lot of moisture, so a large share of the cooling load is latent, water the coil has to remove.
What drives loads in Tampa
Cooling dominates. The 1% design temperature is 91°F with 53 design grains, so moisture removal is a big slice of the load. The low daily range, about 13°F in July, means nights stay warm and the house never gets much relief to coast on.
Attic ductwork and west glass decide most of the room-to-room differences. Many Tampa ranch homes have air handlers in the garage and ducts in a vented attic; leaky or poorly insulated attic ducts can add more load than an extra window.
Typical loads for Tampa homes
Four illustrative houses, each with 8-foot ceilings and ducts in a vented attic unless noted, at the design conditions above:
| House | Heating load | Cooling load | Nominal size | Sq ft per ton |
|---|---|---|---|---|
| Older 1,500 sq ft one-story fair insulation, double-pane windows | 24,929 Btuh | 31,569 Btuh | 3 tons | 570 |
| 2,000 sq ft one-story, built to code good insulation, low-E windows | 21,456 Btuh | 28,384 Btuh | 2.5 tons | 846 |
| 2,600 sq ft two-story, built to code good insulation, low-E windows | 23,677 Btuh | 32,687 Btuh | 3 tons | 955 |
| 2,000 sq ft high-performance excellent insulation and air sealing, ducts inside | 15,531 Btuh | 22,915 Btuh | 2 tons | 1,047 |
The spread is the point. The older 1,500 sq ft house needs 24,929 Btuh of heat, more than the 2,000 sq ft high-performance house at 15,531 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.
Common sizing mistakes in Tampa
- Copying the old system's tonnage after a reroof, window replacement or attic insulation upgrade. Those changes cut the load, so the old size is usually too big now.
- Using a Miami or Orlando number. Tampa's 43°F heating and 91°F cooling design temperatures are their own; use the Tampa station.
- Skipping duct leakage. A leaky return in a hot attic pulls in moist attic air and makes humidity worse.
Heat pumps in Tampa
A heat pump covers Tampa's heating load comfortably. Size it to the cooling load and use variable-speed or two-stage equipment if humidity control matters, which in Tampa it almost always does. The heat pump sizing guide covers reading capacity at 47°F and 17°F and setting the balance point.
Run a load for your Tampa house
The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.
FAQ
Do I need strip heat with a heat pump in Tampa?
Usually only a small amount, for defrost comfort and the rare cold snap. At a 43°F design temperature, a heat pump sized for cooling normally carries the whole heating load. Check the heat pump's capacity at 47°F and 17°F against your calculated heat loss.
What is the Manual J design temperature for Tampa, FL?
NOAA’s Engineering Weather Data lists Tampa International Airport at 43°F for the 99% heating design and 91°F for the 1% cooling design, with a 77°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.
What size AC do I need for a 2,000 sq ft house in Tampa?
It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in a vented attic comes out at about 28,384 Btuh of cooling, a 2.5-ton nominal size, or about 846 sq ft per ton. An older or leakier house needs more; run a load for the actual house.