Scope. Outdoor design conditions and illustrative block loads for homes in and around San Diego, CA. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.

San Diego design conditions

Weather stationSan Diego International Airport (Lindbergh Field) (KSAN)
SourceNOAA NCEI Engineering Weather Data, 1988–2017 observations
Elevation17 ft
99% heating design temperature (NOAA/ASHRAE)46°F
1% cooling design temperature (NOAA/ASHRAE)81°F
Mean coincident wet bulb65°F
Design grains (75°F, 50% RH indoors)5
Daily rangeLow (July average 8°F)
IECC climate zone3B (San Diego County, 2021 IECC)
Nearby stationMCAS Miramar (inland) (KNKX): 43°F heating, 90°F cooling

With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 24°F difference and the cooling load by a 6°F difference, before sun, people and moisture are added. 5 design grains means a real latent load on top of the sensible load, so the equipment has to dehumidify as well as cool.

What drives loads in San Diego

NOAA lists San Diego International (Lindbergh Field) at 81°F cooling and 46°F heating, with a low daily range. Inland, MCAS Miramar is 90°F and 43°F, and the valleys further east are hotter.

Low loads mean small equipment. A typical coastal home often lands at the smallest sizes manufacturers make, which is where multi-zone ductless and variable-speed systems help.

Typical loads for San Diego homes

Four illustrative houses, each with 8-foot ceilings and ducts in a vented attic unless noted, at the design conditions above:

HouseHeating loadCooling loadNominal sizeSq ft per ton
Older 1,500 sq ft one-story
fair insulation, double-pane windows
22,782 Btuh20,332 Btuh2 tons885
2,000 sq ft one-story, built to code
good insulation, low-E windows
19,639 Btuh19,200 Btuh2 tons1,250
2,600 sq ft two-story, built to code
good insulation, low-E windows
21,648 Btuh21,705 Btuh2 tons1,437
2,000 sq ft high-performance
excellent insulation and air sealing, ducts inside
14,262 Btuh16,344 Btuh1.5 tons1,468

The spread is the point. The older 1,500 sq ft house needs 22,782 Btuh of heat, more than the 2,000 sq ft high-performance house at 14,262 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.

Common sizing mistakes in San Diego

  • Using a coastal design temperature for an inland house, or the reverse.
  • Buying a 3-ton system for a house with a 1.5-ton load because 3 tons is “normal.”
  • Skipping the heating side. Even in San Diego, a drafty house needs some heat on a 46°F night.

Heat pumps in San Diego

A heat pump covers San Diego heating with ease. The challenge is the other direction: finding equipment small enough, or variable enough, for a very small load. The heat pump sizing guide covers reading capacity at 47°F and 17°F and setting the balance point.

Run a load for your San Diego house

The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.

FAQ

Do I need central AC in San Diego?

Near the coast, often not much of it. The 81°F design temperature at Lindbergh Field produces small loads. A Manual J shows whether a small ducted system, a ductless unit or just better shading and ventilation fits the house.

What is the Manual J design temperature for San Diego, CA?

NOAA’s Engineering Weather Data lists San Diego International Airport (Lindbergh Field) at 46°F for the 99% heating design and 81°F for the 1% cooling design, with a 65°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.

What size AC do I need for a 2,000 sq ft house in San Diego?

It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in a vented attic comes out at about 19,200 Btuh of cooling, a 2-ton nominal size, or about 1,250 sq ft per ton. An older or leakier house needs more; run a load for the actual house.