Scope. Outdoor design conditions and illustrative block loads for homes in and around Minneapolis, MN. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.
Minneapolis design conditions
| Weather station | Minneapolis-St. Paul International Airport (KMSP) |
|---|---|
| Source | NOAA NCEI Engineering Weather Data, 1988–2017 observations |
| Elevation | 841 ft |
| 99% heating design temperature (NOAA/ASHRAE) | −6°F |
| 1% cooling design temperature (NOAA/ASHRAE) | 88°F |
| Mean coincident wet bulb | 72°F |
| Design grains (75°F, 50% RH indoors) | 29 |
| Daily range | Medium (July average 17°F) |
| IECC climate zone | 6A (Hennepin County, 2021 IECC) |
With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 76°F difference and the cooling load by a 13°F difference, before sun, people and moisture are added. 29 design grains means a real latent load on top of the sensible load, so the equipment has to dehumidify as well as cool.
What drives loads in Minneapolis
NOAA lists Minneapolis-St. Paul International at 88°F cooling and −6°F heating, with 29 design grains.
Basements are nearly universal. New homes are built very tight, older ones much less so. Ice dams on older roofs are a symptom of the same heat loss the Manual J measures.
Typical loads for Minneapolis homes
Four illustrative houses, each with 8-foot ceilings and ducts in the basement unless noted, at the design conditions above:
| House | Heating load | Cooling load | Nominal size | Sq ft per ton |
|---|---|---|---|---|
| Older 1,500 sq ft one-story fair insulation, double-pane windows | 60,801 Btuh | 24,842 Btuh | 2.5 tons | 725 |
| 2,000 sq ft one-story, built to code good insulation, low-E windows | 51,676 Btuh | 22,445 Btuh | 2 tons | 1,069 |
| 2,600 sq ft two-story, built to code good insulation, low-E windows | 57,227 Btuh | 25,742 Btuh | 2.5 tons | 1,212 |
| 2,000 sq ft high-performance excellent insulation and air sealing, ducts inside | 40,018 Btuh | 20,002 Btuh | 2 tons | 1,200 |
The spread is the point. The older 1,500 sq ft house needs 60,801 Btuh of heat, more than the 2,000 sq ft high-performance house at 40,018 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.
Common sizing mistakes in Minneapolis
- Oversizing the furnace. Long, steady run times keep a Minnesota house more comfortable than short blasts.
- Choosing a heat pump by its 47°F rating. At −6°F, only capacity at 5°F and below matters.
- Ignoring ventilation. Tight new homes need it, and the outdoor air adds to the heating load.
Heat pumps in Minneapolis
Cold-climate heat pumps are increasingly used here, usually with a gas furnace or electric backup sized for the gap between heat pump capacity and the heat loss at −6°F. The cold-climate heat pump guide walks through capacity at the design temperature, the balance point and backup heat.
Run a load for your Minneapolis house
The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.
FAQ
Can a heat pump work in Minneapolis?
Yes, as part of the system. A cold-climate heat pump carries most hours of the winter; backup heat covers the coldest ones. Size both from a Manual J heat loss at the −6°F design temperature.
What is the Manual J design temperature for Minneapolis, MN?
NOAA’s Engineering Weather Data lists Minneapolis-St. Paul International Airport at −6°F for the 99% heating design and 88°F for the 1% cooling design, with a 72°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.
What size AC do I need for a 2,000 sq ft house in Minneapolis?
It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in the basement comes out at about 22,445 Btuh of cooling, a 2-ton nominal size, or about 1,069 sq ft per ton. An older or leakier house needs more; run a load for the actual house.