Scope. Outdoor design conditions and illustrative block loads for homes in and around Miami, FL. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.

Miami design conditions

Weather stationMiami International Airport (KMIA)
SourceNOAA NCEI Engineering Weather Data, 1988–2017 observations
Elevation8 ft
99% heating design temperature (NOAA/ASHRAE)53°F
1% cooling design temperature (NOAA/ASHRAE)91°F
Mean coincident wet bulb78°F
Design grains (75°F, 50% RH indoors)57
Daily rangeLow (July average 12°F)
IECC climate zone1A (Miami-Dade County, 2021 IECC)
Nearby stationKendall-Tamiami Executive Airport (KTMB): 50°F heating, 91°F cooling

With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 17°F difference and the cooling load by a 16°F difference, before sun, people and moisture are added. 57 design grains is a lot of moisture, so a large share of the cooling load is latent, water the coil has to remove.

What drives loads in Miami

The 1% cooling design temperature is only 91°F, lower than Dallas or Phoenix. What makes Miami hard is the air's moisture: at 57 grains above a 50% RH indoor target, a large share of the cooling load is latent, meaning water the coil has to wring out rather than heat it has to remove.

Glass is the next big driver. Impact-rated windows are standard in South Florida, and their low solar heat gain coefficient helps, but large west-facing sliders still push the afternoon peak. Ducts in a vented attic add gain on top, because Florida attics run far hotter than the outdoor air.

Typical loads for Miami homes

Four illustrative houses, each with 8-foot ceilings and ducts in a vented attic unless noted, at the design conditions above:

HouseHeating loadCooling loadNominal sizeSq ft per ton
Older 1,500 sq ft one-story
fair insulation, double-pane windows
17,141 Btuh31,626 Btuh3 tons569
2,000 sq ft one-story, built to code
good insulation, low-E windows
14,981 Btuh28,461 Btuh2.5 tons843
2,600 sq ft two-story, built to code
good insulation, low-E windows
16,366 Btuh32,764 Btuh3 tons952
2,000 sq ft high-performance
excellent insulation and air sealing, ducts inside
11,080 Btuh22,996 Btuh2 tons1,044

The spread is the point. The older 1,500 sq ft house needs 17,141 Btuh of heat, more than the 2,000 sq ft high-performance house at 11,080 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.

Common sizing mistakes in Miami

  • Oversizing “to be safe.” An oversized system satisfies the thermostat before it has run long enough to pull moisture, and the house ends up cool and clammy.
  • Ignoring the sensible heat ratio. Check that the equipment's latent capacity at your airflow covers the latent load, not just the total tonnage.
  • Sizing the heat strips to the cooling tonnage. With a 53°F heating design temperature, the heating load is small; most heat pumps carry it without large strip heat.

Heat pumps in Miami

Heat pumps are the default here and heating capacity is never the limit. Choose by cooling and moisture removal: variable-speed equipment that runs long, slow cycles holds humidity far better than a single-stage unit sized up. The heat pump sizing guide covers reading capacity at 47°F and 17°F and setting the balance point.

Run a load for your Miami house

The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.

FAQ

Why does a Manual J in Miami come out smaller than 500 sq ft per ton?

Because modern Miami homes have impact glass, better insulation and tighter construction than the houses those rules came from. The design temperature is only 91°F; humidity is the hard part, and that is solved by run time and latent capacity, not extra tonnage.

What is the Manual J design temperature for Miami, FL?

NOAA’s Engineering Weather Data lists Miami International Airport at 53°F for the 99% heating design and 91°F for the 1% cooling design, with a 78°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.

What size AC do I need for a 2,000 sq ft house in Miami?

It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in a vented attic comes out at about 28,461 Btuh of cooling, a 2.5-ton nominal size, or about 843 sq ft per ton. An older or leakier house needs more; run a load for the actual house.