Scope. Outdoor design conditions and illustrative block loads for homes in and around Kansas City, MO. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.

Kansas City design conditions

Weather stationKansas City International Airport (KMCI)
SourceNOAA NCEI Engineering Weather Data, 1988–2017 observations
Elevation1,026 ft
99% heating design temperature (NOAA/ASHRAE)7°F
1% cooling design temperature (NOAA/ASHRAE)93°F
Mean coincident wet bulb76°F
Design grains (75°F, 50% RH indoors)47
Daily rangeMedium (July average 18°F)
IECC climate zone4A (Jackson County, 2021 IECC)

With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 63°F difference and the cooling load by a 18°F difference, before sun, people and moisture are added. 47 design grains is a lot of moisture, so a large share of the cooling load is latent, water the coil has to remove.

What drives loads in Kansas City

NOAA lists Kansas City International at 93°F cooling and 7°F heating, with 47 design grains, high for the Plains.

Basements are common, often partly finished, with the furnace and ducts below the main floor. How the basement is treated in the load, conditioned or not, swings the heating number a lot.

Typical loads for Kansas City homes

Four illustrative houses, each with 8-foot ceilings and ducts in the basement unless noted, at the design conditions above:

HouseHeating loadCooling loadNominal sizeSq ft per ton
Older 1,500 sq ft one-story
fair insulation, double-pane windows
48,417 Btuh29,510 Btuh2.5 tons610
2,000 sq ft one-story, built to code
good insulation, low-E windows
40,874 Btuh26,399 Btuh2.5 tons909
2,600 sq ft two-story, built to code
good insulation, low-E windows
45,697 Btuh30,477 Btuh3 tons1,024
2,000 sq ft high-performance
excellent insulation and air sealing, ducts inside
31,526 Btuh23,077 Btuh2 tons1,040

The spread is the point. The older 1,500 sq ft house needs 48,417 Btuh of heat, more than the 2,000 sq ft high-performance house at 31,526 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.

Common sizing mistakes in Kansas City

  • Leaving the basement out of the load when it is heated and lived in.
  • Assuming a big furnace fixes cold rooms. Uneven heat is usually airflow or duct design, not capacity.
  • Underestimating summer moisture. At 47 design grains, latent load is significant.

Heat pumps in Kansas City

At 7°F, a standard heat pump needs substantial backup. Cold-climate heat pumps or a dual-fuel setup with a gas furnace are the usual answers. The cold-climate heat pump guide walks through capacity at the design temperature, the balance point and backup heat.

Run a load for your Kansas City house

The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.

FAQ

Is a heat pump practical in Kansas City?

Yes, with the right equipment. At a 7°F design temperature, look at a cold-climate model's capacity at 5°F or pair a heat pump with a gas furnace, and size from the Manual J heat loss.

What is the Manual J design temperature for Kansas City, MO?

NOAA’s Engineering Weather Data lists Kansas City International Airport at 7°F for the 99% heating design and 93°F for the 1% cooling design, with a 76°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.

What size AC do I need for a 2,000 sq ft house in Kansas City?

It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in the basement comes out at about 26,399 Btuh of cooling, a 2.5-ton nominal size, or about 909 sq ft per ton. An older or leakier house needs more; run a load for the actual house.