Scope. Outdoor design conditions and illustrative block loads for homes in and around Charlotte, NC. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.
Charlotte design conditions
| Weather station | Charlotte Douglas International Airport (KCLT) |
|---|---|
| Source | NOAA NCEI Engineering Weather Data, 1988–2017 observations |
| Elevation | 748 ft |
| 99% heating design temperature (NOAA/ASHRAE) | 25°F |
| 1% cooling design temperature (NOAA/ASHRAE) | 92°F |
| Mean coincident wet bulb | 74°F |
| Design grains (75°F, 50% RH indoors) | 34 |
| Daily range | Medium (July average 19°F) |
| IECC climate zone | 3A (Mecklenburg County, 2021 IECC) |
With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 45°F difference and the cooling load by a 17°F difference, before sun, people and moisture are added. 34 design grains means a real latent load on top of the sensible load, so the equipment has to dehumidify as well as cool.
What drives loads in Charlotte
NOAA lists Charlotte Douglas at 92°F cooling and 25°F heating, with 34 design grains and a medium daily range.
Many homes have ducts in a vented crawlspace, an attic, or both. Crawlspace ducts lose heat in winter and add moisture risk in summer; sealed and conditioned crawlspaces change the load meaningfully.
Typical loads for Charlotte homes
Four illustrative houses, each with 8-foot ceilings and ducts in a vented crawlspace unless noted, at the design conditions above:
| House | Heating load | Cooling load | Nominal size | Sq ft per ton |
|---|---|---|---|---|
| Older 1,500 sq ft one-story fair insulation, double-pane windows | 37,177 Btuh | 28,900 Btuh | 2.5 tons | 623 |
| 2,000 sq ft one-story, built to code good insulation, low-E windows | 31,599 Btuh | 25,965 Btuh | 2.5 tons | 924 |
| 2,600 sq ft two-story, built to code good insulation, low-E windows | 35,166 Btuh | 29,926 Btuh | 2.5 tons | 1,043 |
| 2,000 sq ft high-performance excellent insulation and air sealing, ducts inside | 23,487 Btuh | 21,750 Btuh | 2 tons | 1,103 |
The spread is the point. The older 1,500 sq ft house needs 37,177 Btuh of heat, more than the 2,000 sq ft high-performance house at 23,487 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.
Common sizing mistakes in Charlotte
- Using attic duct inputs for a crawlspace system, or the other way round.
- Skipping infiltration. Older Charlotte homes leak a lot, and leakage is a big part of the winter load.
- Sizing a heat pump without checking capacity at 25°F.
Heat pumps in Charlotte
Heat pumps are common across the Charlotte area. Check the unit's capacity at 17°F, set the balance point and size auxiliary heat from the Manual J heat loss. The heat pump sizing guide covers reading capacity at 47°F and 17°F and setting the balance point.
Run a load for your Charlotte house
The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.
FAQ
Does a sealed crawlspace change my Charlotte load calculation?
Yes. Ducts inside a sealed, conditioned crawlspace lose far less heat in winter and gain less moisture in summer than ducts in a vented one. Enter the duct location the house actually has.
What is the Manual J design temperature for Charlotte, NC?
NOAA’s Engineering Weather Data lists Charlotte Douglas International Airport at 25°F for the 99% heating design and 92°F for the 1% cooling design, with a 74°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.
What size AC do I need for a 2,000 sq ft house in Charlotte?
It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in a vented crawlspace comes out at about 25,965 Btuh of cooling, a 2.5-ton nominal size, or about 924 sq ft per ton. An older or leakier house needs more; run a load for the actual house.