Scope. Outdoor design conditions and illustrative block loads for homes in and around Sacramento, CA. The example loads are estimates for typical houses, not a design for yours. Your building department may require specific design values. Not ACCA approved or certified, and not a stamped design.
Sacramento design conditions
| Weather station | Sacramento Executive Airport (KSAC) |
|---|---|
| Source | NOAA NCEI Engineering Weather Data, 1988–2017 observations |
| Elevation | 24 ft |
| 99% heating design temperature (NOAA/ASHRAE) | 34°F |
| 1% cooling design temperature (NOAA/ASHRAE) | 97°F |
| Mean coincident wet bulb | 68°F |
| Design grains (75°F, 50% RH indoors) | -7 |
| Daily range | High (July average 32°F) |
| IECC climate zone | 3B (Sacramento County, 2021 IECC) |
With Manual J’s default indoor conditions of 70°F in winter and 75°F in summer, the heating load is driven by a 36°F difference and the cooling load by a 22°F difference, before sun, people and moisture are added. Design grains are negative, which means the outdoor air at the design condition is drier than the indoor target: the cooling load is almost entirely sensible.
What drives loads in Sacramento
NOAA lists Sacramento Executive Airport at 97°F cooling and 34°F heating, with a high daily range and negative design grains.
Ducts in a hot attic and west glass carry the peak. Because nights cool off, the house can shed stored heat, and a right-sized system has time to recover.
Typical loads for Sacramento homes
Four illustrative houses, each with 8-foot ceilings and ducts in a vented attic unless noted, at the design conditions above:
| House | Heating load | Cooling load | Nominal size | Sq ft per ton |
|---|---|---|---|---|
| Older 1,500 sq ft one-story fair insulation, double-pane windows | 32,100 Btuh | 27,733 Btuh | 2.5 tons | 649 |
| 2,000 sq ft one-story, built to code good insulation, low-E windows | 27,386 Btuh | 24,600 Btuh | 2.5 tons | 976 |
| 2,600 sq ft two-story, built to code good insulation, low-E windows | 30,399 Btuh | 28,507 Btuh | 2.5 tons | 1,094 |
| 2,000 sq ft high-performance excellent insulation and air sealing, ducts inside | 19,591 Btuh | 19,681 Btuh | 2 tons | 1,219 |
The spread is the point. The older 1,500 sq ft house needs 32,100 Btuh of heat, more than the 2,000 sq ft high-performance house at 19,591 Btuh, despite being 500 sq ft smaller. No square-foot rule can see that. These are whole-house block loads from the same engine the free Manual J calculator and the app use; a room-by-room load for a real house will differ.
Common sizing mistakes in Sacramento
- Ignoring the daily range input. A high daily range lowers the cooling load compared with a low-range city at the same design temperature.
- Sizing to a record heat wave.
- Skipping California's own rules. Title 24 has requirements for load calculation and duct sealing; check what the building department expects.
Heat pumps in Sacramento
Heat pumps suit Sacramento well. Winters are mild, and California's push toward electrification makes them the most common replacement choice. The heat pump sizing guide covers reading capacity at 47°F and 17°F and setting the balance point.
Run a load for your Sacramento house
The free Manual J calculator takes a ZIP code and eight inputs and returns a whole-house heating and cooling load in the browser. The HVAC Load Calculator app goes further at the house: room-by-room loads, Manual S equipment sizes and a PDF report.
FAQ
Why does the daily range matter in Sacramento?
Manual J uses the daily range to adjust cooling loads. A high range means cooler nights, which lowers the load through walls and roofs. Sacramento's high range is part of why a correct load is smaller than a same-temperature city with warm nights.
What is the Manual J design temperature for Sacramento, CA?
NOAA’s Engineering Weather Data lists Sacramento Executive Airport at 34°F for the 99% heating design and 97°F for the 1% cooling design, with a 68°F mean coincident wet bulb, from 1988–2017 observations. Use the station closest to the house in climate, and any value your building department requires.
What size AC do I need for a 2,000 sq ft house in Sacramento?
It depends on the house, not the floor area. In our example, a code-built 2,000 sq ft one-story with low-E windows and ducts in a vented attic comes out at about 24,600 Btuh of cooling, a 2.5-ton nominal size, or about 976 sq ft per ton. An older or leakier house needs more; run a load for the actual house.