Scope. A working overview of the ACCA residential design sequence in the US. Percentages below are the commonly cited limits; the current text of each manual and your local code govern. Manual J, Manual S, Manual D and Manual T are registered marks of ACCA, and this guide is independent of ACCA.
The sequence at a glance
| Manual | Question it answers | Hands the next step | Shortcut it replaces |
|---|---|---|---|
| J — load calculation | How much heating and cooling does this house need on a design day? | Heating load; sensible and latent cooling loads; room loads | Square feet per ton |
| S — equipment selection | Which actual equipment delivers that, at these design conditions? | Selected equipment, its airflow and blower performance | “Same size as the old one” |
| D — duct design | What duct sizes carry that airflow to each room within the blower’s pressure budget? | Duct sizes and layout | “6-inch to every room” |
| T — air distribution | Which supply and return outlets deliver that air comfortably and quietly? | Register and grille selection | Whatever the supply house has |
The order is not paperwork for its own sake. Each step needs a number only the previous step can produce.
Manual J: the load
Manual J calculates the house’s heat loss and heat gain at design conditions, from the envelope, glass, air leakage, ventilation, occupants and ducts. The output is in Btuh, not tons, and it is split into sensible and latent cooling. A room-by-room Manual J also gives each room’s load, and so its share of the airflow. The what is Manual J guide walks through it in detail.
Manual S: the equipment
Manual S selects equipment against the Manual J loads using the manufacturer’s expanded performance data at the job’s design conditions — not the nominal tonnage on the box, which is a rating-point number. A “3-ton” condenser can deliver noticeably more or less than 36,000 Btuh depending on the coil it is matched with, the airflow and the outdoor temperature.
The rules are a window, not a target. The commonly cited limits are:
- Cooling: sensible capacity has to cover the sensible load and latent capacity the latent load, while total capacity stays at no more than about 115% of the total cooling load for single-speed equipment, or the next nominal size up where no standard size lands inside.
- Heat pumps where heating dominates: more room on the cooling side, commonly cited as up to 125%, so the unit can carry more of the winter. The 2023 edition (ANSI/ACCA 3 Manual S) widened tolerances further for variable-capacity heat pumps.
- Furnaces: output capacity from 100% to 140% of the heating load.
Check the edition you are working to; the limits have been revised, and the current one splits them by equipment type and climate. Manual S also checks airflow: the selected air handler or furnace blower has to move the air the coil needs against the static pressure the ducts will present, which is the bridge into Manual D.
Size by size, the cooling window looks like the table in what size AC unit do I need, and the heating side is in what size furnace do I need.
Manual D: the ducts
Manual D sizes the duct system for the selected equipment. It starts from the blower, not the ducts:
- Read the blower table for the external static pressure the equipment can produce at the design airflow.
- Subtract every component pressure drop in the path — coil, filter, supply registers, return grilles, balancing dampers. What is left is the available static pressure (ASP) for the ductwork itself.
- Find the total effective length (TEL) of the longest supply run plus the longest return run, counting each fitting at its equivalent length.
- Divide: friction rate = ASP × 100 ÷ TEL, in inches of water column per 100 feet.
- Size each run from its room airflow (from the room-by-room Manual J) and that friction rate, and check velocity limits.
Example. A blower rated for 0.50 in. w.c. at the design airflow. The coil takes 0.18, the filter 0.08, supply and return grilles 0.06 together and a balancing damper 0.03, so 0.35 is spoken for and 0.15 is available. With a total effective length of 250 feet, the design friction rate is 0.15 × 100 ÷ 250 = 0.06 in. per 100 ft, inside the healthy range most designers aim for. Stack on a restrictive filter and a long return and that same blower has almost nothing left for the ducts.
The duct static pressure and friction rate guide covers the field side of this, and the free ductulator sizes a run from CFM and friction rate.
Manual T: the outlets
Manual T selects supply registers and return grilles: throw, spread, face velocity and noise. A duct system can deliver the right CFM to a room and still make it uncomfortable if the register dumps the air on the couch or whistles. It is the step most often skipped, and the one homeowners notice first.
What happens when a step is skipped
Here is the failure in its most common form. A 2,000 sq ft house gets sized by the 400-square-feet-per-ton rule: 5 tons, which wants roughly 2,000 CFM at a typical 400 CFM per ton. A real Manual J would have said 3 tons, about 1,200 CFM, and the existing ducts were sized for something close to that.
Duct friction rises roughly with the square of airflow. Pushing 2,000 CFM through ducts built for 1,200 means close to (2,000 ÷ 1,200)² ≈ 2.8 times the pressure drop. The blower cannot get there, so the system ends up short of its own rated airflow, noisy at the registers, running high static, and cooling the house fast enough to shut off before it dehumidifies. Every symptom traces back to a skipped Manual J, and none of them is fixed by a better condenser.
The opposite skip hurts too. A correct Manual J and Manual S followed by “6-inch to every room” still starves the far bedrooms and over-delivers to the room next to the air handler.
What code asks for
The International Residential Code links the steps: section M1401.3 calls for equipment sized with Manual S from loads calculated with Manual J or another approved method, and the duct chapter points duct design at Manual D. The IECC carries a matching equipment-sizing requirement. How strictly that is enforced, and on which jobs, depends on your jurisdiction. Some building departments review all three reports at plan review; many never ask on a replacement.
Tools for each step
- Manual J: the free Manual J calculator for a whole-house block load in the browser, or the HVAC Load Calculator app for Manual J 8th Edition methods offline at the house.
- Manual S: the app’s results show the AC tonnages, furnace sizes and heat pump sizes that fit the calculated load, with oversize warnings and a heat pump balance point. Confirm the specific unit against its expanded performance data.
- Manual D: the Static Pressure & Duct Check app reads total external static, checks what a duct can move, and designs a Manual D-style duct schedule offline.
FAQ
What is the difference between Manual J and Manual S?
Manual J is the load in Btuh. Manual S picks equipment whose real capacity at design conditions fits it, inside limits like about 115% for single-speed cooling and 100–140% for furnaces.
Which comes first, Manual J, S or D?
J, then S, then D, then T. Each needs a number only the step before it produces: loads, then equipment airflow and blower data, then duct sizes.
What is the Manual S oversizing limit for air conditioners?
About 115% of total cooling load for single-speed equipment, or the next nominal size if nothing fits. Heat pumps where heating dominates get more room, commonly 125%. Check your edition.
How do you calculate friction rate for Manual D?
Available static pressure × 100 ÷ total effective length. 0.15 in. available over 250 ft of effective length is 0.06 in. per 100 ft.
Is a Manual J enough without Manual D?
Enough to size the equipment, not to know the ducts can carry the air. On a replacement, at least measure total external static before you trust the old ducts.